• 15A 120V switches OFF when sense cord is powered
• Used to inhibit Co2, dehumidifyers and/or other equipment while venting is in progress

• Safely switch high amperage equipment with low cost timer
• Incorporate 0 to 20 minutes ON delay
• prevent hot bulb start-ups or sequence turn-ons to reduce electrical system loading
• 240V capacity

The Can Filters Group Inc. has added thermostatically controlled fans in sizes 4 HO and 6 HO, 240 volt 60 hz. The new thermostatic fan is controlled by setting the dial to the desired temperature. The fan has an integrated sensor inside, sensing the temperature of the airflow every 1.5 minutes. When the airflow temperature is warmer than the dial setting, the fan will automatically speed up. If the air flow is cooler then the set point, the fan will automatically slow down.
This Thermostatic fan will maintain air flow at the low speed until higher speed is required.
No remote sensors no problem!

The Can Filters Group Inc. has added thermostatically controlled fans in sizes 4 HO and 6 HO, 240 volt 60 hz. The new thermostatic fan is controlled by setting the dial to the desired temperature. The fan has an integrated sensor inside, sensing the temperature of the airflow every 1.5 minutes. When the airflow temperature is warmer than the dial setting, the fan will automatically speed up. If the air flow is cooler then the set point, the fan will automatically slow down.
This Thermostatic fan will maintain air flow at the low speed until higher speed is required.
No remote sensors no problem!

The CDMC-6 system is designed to sample the air and learn the characteristics of your space, then make adjustments as necessary to ensure a constant level of CO2. The CDM-6000 works in conjunction with the CDDS-2 controller (sequencer) to effectively enrich indoor gardens and greenhouses with CO2 or reconfigured the system mode to vent excess CO2 if desired.

FEATURES

• Built-in Photo Sensor for enhanced control
• Easy to program and operate with adjustable hysteresis (differential)
• Programmed for overshoot protection logic
• Durable infrared sensor
• CO2 measurement range from 0-5000 PPM
• CO2 control range from 300-5000 PPM
• Easy to read LED display light will not affect plant growth
• Mode indicator LEDs
• Factory calibrated and inspected for precision performance
• Operates on 120 VAC at 60 Hz, 12 Amp switching capacity
• Manufactured in Oregon, USA

• Controller with high temperature shut-off function 120v 15 amps

• Easy to set up and install an economical solution to automate CO2 functions

• Compatible with any 120v CO2 regulators and generators

• Control a CO2 bottle or generator

• Shut off CO2 enrichment when temperature is too high

• Can be used for CO2 extraction

• Shut off ventilation when temperature is too low

• Warranty: 1 year

CO2 Set Point Controller

• Set and Forget; easy to install and operate

• Factory calibrated and inspected for precision performance

• Preset hysteresis (differential) of 20 PPM

• Photo Sensor to defeat CO2 enrichment at night (dark)

• Large LED display w/real-time CO2 PPM

• Orange LED to indicate when CO2 enrichment is active

• Elevation adjustment for improved accuracy

• Fully integrable with other atmospheric controllers or timers

• Durable black anodized aluminum chassis resists rusting, corrosion and scratching

• Red illuminated power switch

• 14 AWG, SJTW rated piggy back power cord

• Operates on 120 VAC at 60 Hz, 12 Amp switching capacity

• Seamless intergrationof Co2 enrichment and intake/exhaust ventilation.
• Co2, relative humidity and temperature precise electronic sensors.
• 24 hour datalogging of sensor values.
• Alarm system hook-up (with iMS-100).

The CT-DH-1 is designed to turn "On" exhaust and/or intake fans to remove excess or unwanted heat and humidity. Set your desired temperature and humidity using the dials. Internal sensors will allow a 7F temperature comfort zone (3F with an external coil or remote bulb) and a 5% humidity span (differential) between the time the fans activate for cooling or dehumidifying and then turn "Off" again. Plug-in and control circulation fans, exhaust fans, cooling systems, or dehumidifiers. The outlets on the CT-DH-1 are integrated, so that when either the temperature or humidity settings are exceeded, all four will activate, turning "On" equipment plugged into any of the four outlets.

The CT-DH-1 operates on 120 Volt AC with 15 Amp maximum switching capacity and is intended for indoor use only. Be sure to locate your atmospheric controller where it will accurately sample and respond to the average air conditions. Good air circulation around the controller and in your garden space is essential. Avoid locating the controller in a draft or in direct sunlight.

The CT-DH-2 is also designed to turn "On" cooling and dehumidifying equipment to remove excess heat and humidity. However, the CT-DH-2 offers you independent outlets for heating or cooling. The left outlets activate when temperature exceeds your set point. The right outlets activate when humidity exceed your set point. Set your desired temperature and humidity using the dials. Internal sensors will allow a 7F temperature comfort zone (3F with an external coil or remote bulb) and a 5% humidity span (differential) between the time the fans activate for cooling or dehumidifying and then turn "Off" again.

The CT-DH-2 operates on 120 Volt AC with 15 Amp maximum switching capacity and is intended for indoor use only. Be sure to locate your atmospheric controller where it will accurately sample and respond to the average air conditions. Good air circulation around the controller and in your garden space is essential. Avoid locating the controller in a draft or in direct sunlight.

While the CT-DH-3 has many applications, it was primarily developed for use with CO2 equipment and exhaust/ventilation fans. The left side (or equipment) outlets of the controller are normally "ON" until defeated when the right side outlets are activated. Internal sensors will allow for 7F temperature zone and a 5% humidity differential between the time that the fans come "ON" and then turn "OFF" again. When temperature or humidity rises above your dial set points, the right outlets will activate and the left outlets will deactivate. The right side outlets will remain "ON" until the temperature drops 7 and/or the humidity drops 5% below your set points. At which time, the right outlets will shut "OFF" and reactivate the left outlets.

The CT-DH-3 operates on 120 Volt AC with 15 Amp maximum switching capacity and is intended for indoor use only. Be sure to locate your atmospheric controller where it will accurately sample and respond to the average air conditions. Good air circulation around the controller and in your garden space is essential. Avoid locating the controller in a draft or in direct sunlight.

The CT-DH-4 and 4P are designed to be used with CO2 equipment, dehumidifiers, and exhaust fans. While it is similar to the CT-DH-3 it has the added feature of independent outlets for temperature and humidity control. It is ideally suited for use with dehumidifiers. Temperature above your set point will activate the right hand outlets and deactivate the bottom left "CO2" outlet. Humidity will activate the top left "Dehumidify" outlet. Internal sensors will allow a 7 temperature comfort zone and a 5% humidity (differential) between the time the equipment comes "On" and goes back "Off" again. Set the temperature and humidity to the desired settings. The CO2 outlet is normally in the "On" position and is able to activate CO2 equipment as needed. An optional photosensor will defeat CO2 enrichment during darkness hours. Intended for indoor use only. The CT-DH-4 operates on 120 Volts AC with 15 Amp max switching capacity.

The CT-DH-3P is installed for cooling and dehumidifying control (operates on 120 Volt AC with 15 Amp maximum switching capacity and is intended for indoor use only. This unit may be used independently or with many other Green Air Products controls to create an integrated system. When the temperature or humidity raise above the predetermined setting, the CT-DH-3P initiates a venting cycle and CO2 generation is momentarily halted. The Cyclestat is used to time the frequency and duration of the CO2 production. In the event of an exhaust cycle the Cyclestat will reset and immediately replenish CO2 enrichment upon completion of the exhaust function. The CT-DH-3P has a built in photo sensor that prevents CO2 operation during darkness periods. The CO2 generator or emitter system are plugged into the Cyclestat and the Cyclestat is plugged into the left outlets of the CT-DH-3P. The fan is plugged into the right side.

The Cyclestat 4P repeat cycle timer has solved the age old problem of accurate short cycle timing. Perfect for plant zone environments, reptile habitats or any other application requiring automatic short cycle switching. No programming required. Easy to set and operate. Microprocessor time counter with adjustable frequency and duration. The Cyclestat 4P timer has many uses. Only a few of them include: fogging or misting, spray stakes or drip system timing, air pumps, CO2 equipment and intake or exhaust fan control. The Cyclestat may be set for interval and cycle of timed events. Interval is the time between the "On" and "Off" cycles. The interval knob may be set from 5 minutes to 8 hours. Set this for desired time between functions. Cycle is the length of time that a specific function or condition must be maintained. Cycle may be set from 5 seconds to 30 minutes.

Automatic reset feature allows function synchronizing with other system controls. Turn the switch off and on again for manual operation. The Cyclestat 4P has a built-in photosensor to defeat timing during darkness hours. Photosensor may be switched in or out as desired. Operates on 115 volts AC with 15 amp switching capacity. The Cyclestat 4P utilizes a duplex piggy-back power cord which provides a combination plug and receptacle design. Insert plug into 115V wall outlet and plug equipment into piggy back receptacle.

Cycle Timers

• Cycles at 4P - repeat cycle timer

• Easy to install and operate

• Microprocessor controlled, adjustable time counter

• Event time: 5 seconds to 30 minutes

• Interval time: 5 minutes to 8 hours

• Built-in light activated photo sensor with "on-off" switch puts you in control

• Fully integrable with other controls

• Temperature controller without display.
• Can be set to heat of cool with day and night setpoints.

Specially designed for controlling fan blowers and incandescent lamps. Save cash and energy too; simply turn on Dial-A-Temp to desired speed for comfortable heating and start saving. Exclusive features: easy installation with dual plug-in and ground socket. UL recognized components, factory tested. Modern design with rugged fire retardant enclosure.

The DuctStat Temperature Sensitive SwitchTM will turn a device on or off due to temperature rise or temperature fall from the user adjustable set point.

It controls various devices including fans, alarms, heat lamps, lights, and has an adjustable temperature range: 45°F (4°C) to 110°F (43°C). For indoor use only.

The Hydro-Cycle Timer is our most recent development in timing control. It has solved the age old problem of accurate short cycle timing. Perfect for plant zone environments, reptile habitats or any other application requiring automatic short cycle switching. No programming required. Easy to operate. Microprocessor time counter with preset frequency and duration. The Hydro-Cycle timer has many uses. Only a few of them include: fogging or misting, spray stakes or drip system timing, air pumps, CO2 equipment and intake or exhaust fan control. The Hydro-Cycle has a preset interval and cycle time. Interval is the time between the "On" and "Off" cycles. The interval is preset for 4 minutes. Cycle is the length of time that a specific function or condition must be maintained. Cycle is preset for 60 seconds. Automatic reset feature allows function synchronizing with other system controls. Unplug the power cord for manual operation. The Hydro-Cycle timer utilizes a duplex cord cap which provides a combination plug and receptacle power cord design. Operates on 120 volts AC with 15 amp switching capacity. Automatic reset feature allows function synchronizing with other system controls. Turn the switch off and on again for manual operation. The HCT-1 timer utilizes a duplex cord cap which provides a combination plug and receptacle power cord design.

Hydro Cycle Timers

• HCT-1 - Preset cycle timer

• Solid state technology

• Event time (on): 60 seconds; Interval time (off): 4 minutes

Features
- Protects plants by turning off lighting or CO2 generators when temperature is too
high
- Smooth rotating knobs with continuous adjustment
- Restart delay adjustable from 0 to 20 minutes to protect lighting equipment
- High temperature limit adjustable from 70 to 120 °F (21 to 49°C)
- Factory calibrated set knobs for accurate settings
- Precise external temperature sensor on 20 inch cable to place at plants top level:
±1.8°F (±1°C)
- 120 V, maximum outlet current 15 A, 2 HP
- CSA/UL compliant

The CDMC-6 system is designed to sample the air and learn the characteristics of your space, then make adjustments as necessary to ensure a constant level of CO2. The CDM-6000 works in conjunction with the CDDS-2 controller (sequencer) to effectively enrich indoor gardens and greenhouses with CO2 or reconfigured the system mode to vent excess CO2 if desired.

ENRICHMENT or VENTING MODE
The CDMC-6 can be used to operate CO2 producing (enrichment) equipment or CO2 venting (exhaust) equipment. Use the MODE button to quickly and easily switch between enrichment or venting functions. The venting mode is useful for evacuating accumulated CO2 in hospitals, class rooms, factories, conference and meeting rooms, offices, laboratories and mushroom culture facilities.

HOW THE CDMC-6 SYSTEM WORKS
The CDM-6000 samples the air, then sends the sample data to the CDDS-2. The CDDS-2 then activates or deactivates your CO2 enrichment or CO2 venting (exhaust) equipment as necessary to maintain CO2 PPM based on your set point. For best results, turn off all exhaust functions and close all doors and windows during the initial 24-hour adjustment period. You must allow this 24-hour adjustment period, every time you relocate the system to a new space. After 24 hours, you can restart your exhaust functions and continue as normal.

OVERSHOOT PROTECTION LOGIC
In enrichment mode, the CDDS-2 employs a sophisticated adaptive algorithm "Overshoot Protection Logic" which learns the dynamics of the space being controlled. This allows the system to avoid dramatic overshoots inherent to set point controllers or timed CO2 enrichment. These learned parameters are stored in memory, even when the 'POWER' is off, until you reset the CDDS-2.

FEATURES

• Built-in Photo Sensor for enhanced control
• Easy to program and operate with adjustable hysteresis (differential)
• Programmed for overshoot protection logic
• Durable infrared sensor
• CO2 measurement range from 0-5000 PPM
• CO2 control range from 300-5000 PPM
• Easy to read LED display light will not affect plant growth
• Mode indicator LEDs
• Factory calibrated and inspected for precision performance
• Operates on 120 VAC at 60 Hz, 12 Amp switching capacity
• Manufactured in Oregon, USA

• Fits Powerhouse (all)
• Fits Daystar (DAUN)
• Fits Radiant - all vents
• Fits Xtrasun (XT1AC)
• Sunburst

Includes: 2 LG50023 & 1 LG50027

The LT4-120 provides four 10 amp 120 volt outlet receptacles, each capable of powering up to 1000 watts of lighting equipment.

These time switches are designed to operate high load lighting equipment, consisting of a premium quality precision synchronous clock motor and a high amperage switching circuit. All Green Air Products controllers are housed in black anodized brush finish aluminum enclosures which will not break, chip or corrode. Operates with a maximum combined outlet switching capacity of 40 amps.

Plug or wire the power cord into a receptacle capable of handling the maximum total combined amperage draw of your equipment load. Make certain that the receptacle, wiring and circuit breaker are adequate and properly suited for this application. Plug lighting equipment into outlets located on each side of controller. Turn clock dial to current time of day. AM and PM is indicated by colored ring on dial face. Push trippers toward the center of the dial for "On" time and leave in the outward position for "Off" period. Timer has 96 non-detachable 15 minute on\off trippers.

4-Outlet Models

• LT4-120

• LT4-120-LTO 120 V

• LT4-240 240v

• LT4-240-LTO 240v

HIGHLOAD LIGHTING TIMERS

• Easy to program and operate

• Synchronous, motor-driven timeswitch

• 96 daily 15-minute increments

• Optional digital time switch with battery back-up (D)

• Optional latching relay and temperature override (LTO)

• Hard wire ready or cord and plug set